What Is the Difference Between HEA, HEB, HEM and IPE Beams?

HEA, HEB, HEM and IPE are the four most specified European standard beam series, and they are not interchangeable. IPE is a narrow, deep I-section built for bending about its strong axis. HEA, HEB and HEM belong to the wide flange H-section family and share the same basic geometry, differing mainly in flange and web thickness: HEA is the light series, HEB the medium series and HEM the heavy series. Montanstahl produces all four series in stainless steel by laser welding, and the choice between them shapes the weight, stiffness and connection design of every structure they go into.
How Are HEA, HEB, HEM and IPE Beams Standardised?
The dimensions of all four series are defined in EN 10365, the European norm for channels, I and H sections, which brought the older national tables into a single reference. Tolerances on shape and dimensions are covered by EN 10034. Because the series are standardised, a designation such as HEB 200 identifies the same nominal geometry in every European section table and in common structural design software.
The naming also has historical aliases that still appear in drawings and procurement documents. HEA is also known as IPBl, HEB as IPB and HEM as IPBv. Knowing these equivalents avoids confusion when older German or Swiss drawings are reworked, or when a section list has to be matched against a supplier catalogue.
How Do I-Sections and H-Sections Differ in Structural Logic?
All four series have parallel flanges, meaning the inner and outer flange faces run parallel to each other. This distinguishes them from the older IPN series, whose inner flange faces are tapered, and it simplifies bolted connections and welded fabrication. What separates them is the ratio between depth and width. An I-section such as IPE places its material far from the neutral axis in one direction only, while an H-section such as HEB spreads it more evenly in both directions.
That difference decides the job each section does best. IPE delivers the highest bending stiffness for a given weight when the load acts in one plane, which makes it the natural choice for floor beams, purlins and secondary members. HE sections offer more balanced stiffness about both axes and wider flanges, which makes them better suited to columns, heavily loaded beams and members under combined bending and compression.

What Are IPE Beams and Where Are They Used?
IPE beams have a high depth to width ratio. An IPE 200 is 200 mm deep but only 100 mm wide, and its flange width is about half the section depth for smaller sizes, dropping to around 40 percent for the largest sizes. This gives IPE a high moment of inertia per unit mass about the major axis, which is why it is generally the most economical section when the dominant load is bending in one plane. The trade-off is a much lower stiffness about the minor axis, so narrow flanges make IPE more sensitive to lateral torsional buckling when the compression flange is not restrained.
Typical applications are floor and roof beams, mezzanine and platform framing, crane runway girders and support beams for process equipment. The range also includes lighter and heavier variants of the same nominal size: IPE A and IPE AA sections have thinner flanges and webs for weight optimised designs, while IPE O and IPE V sections are reinforced versions for higher loads.
What Is an HEA Beam?
HEA beams are the light series of the European wide flange family, with the thinnest flanges and web of the three. Their actual depth is slightly lower than the nominal size, so an HEA 200 measures 190 by 200 mm. HEA is used where an H-shape is needed for connections or stability but loads are moderate, for example in light columns, frame members and supports.
What Is an HEB Beam?
HEB is the reference section of the family, and its actual depth matches the nominal size: an HEB 200 measures 200 by 200 mm. With thicker flanges and web than HEA, it is the most common choice for primary columns, heavily loaded beams and machine frames, and a common choice for stainless steel building frames exposed to corrosive atmospheres.
What Is an HEM Beam, and How Does It Differ From HEB?
HEM keeps the same geometry as HEB with much thicker flanges and web. The extra material sits on both faces of the flanges and web, so the section becomes deeper and wider than its nominal size: an HEM 200 measures 220 by 206 mm and weighs about 1.7 times as much as an HEB 200. HEM sections are specified where resistance per unit height is decisive, such as heavily loaded columns, press frames and transfer structures.
Above size 300, the flange width of all three series is fixed at about 300 mm and only the depth keeps increasing. Further variants exist at both ends of the range: HEAA is an extra light series below HEA, while HE C and heavy sections designated by depth and mass, such as HE 1000 x 584, extend the range beyond HEB.

Are HEA, HEB, HEM and IPE Beams Available in Stainless Steel?
In carbon steel these sections are typically hot rolled. Montanstahl focuses on stainless steel and produces IPE, HEA, HEB and HEM sections by laser welding, with dimensions according to EN 10365 and tolerances characterised through EN 10034. The stainless sections replicate the geometry of their carbon steel equivalents, so they can be specified with the same designations and section tables in corrosive environments. Laser welding joins flanges and web into a single section with internal radii of 2 mm or less, and allows non-standard geometries up to 1000 mm high, with different flange and web thicknesses up to 80 mm and lengths up to 15 m.
Standard steel grades include 1.4301 (AISI 304) and 1.4404 (AISI 316L), with duplex 1.4462 and super duplex 1.4410 available where higher strength or chloride resistance is required. Typical applications include structures in chemical and pharmaceutical plants, swimming pool halls and water treatment facilities, offshore framing, crane girders in clean production environments and exposed architectural structures. In Europe, design of stainless steel members follows Eurocode 3, in particular EN 1993-1-4, with execution according to EN 1090.
HEA, HEB, HEM and IPE Beams: Comparison Table at Size 200
| Section | Depth h (mm) | Width b (mm) | Web tw (mm) | Flange tf (mm) | Mass (kg/m) | Typical role |
|---|---|---|---|---|---|---|
| IPE 200 | 200 | 100 | 5.6 | 8.5 | 21.8 | Beam in bending |
| HEA 200 (HE 200 A) | 190 | 200 | 6.5 | 10 | 40.9 | Light column or frame member |
| HEB 200 (HE 200 B) | 200 | 200 | 9 | 15 | 60.3 | Primary column or heavy beam |
| HEM 200 (HE 200 M) | 220 | 206 | 15 | 25 | 102.8 | Heavily loaded column |
Values refer to Montanstahl laser welded stainless steel sections and are taken from the HEA, HEB and HEM datasheet and the IPE datasheet. Masses differ slightly from carbon steel tables mainly because laser welded sections have no root radius between web and flanges. At the same nominal size, an IPE 200 weighs about 36 percent of an HEB 200.
Checklist: How to Specify HEA, HEB, HEM or IPE Beams in an RFQ
- State how the member is loaded, as a beam in bending, a column or a member under combined loads, since this is what decides between an IPE and an HE section in the first place.
- Use the full designation with series letter and size, such as HE 200 B or IPE 300, and name the variant where one applies, because IPE A, IPE O and HEAA sections share a nominal size with the standard series but not its dimensions.
- Check available construction depth early: HEB and HEM carry more load within a shallower envelope than a deeper IPE, at the cost of higher mass per metre.
- Confirm the steel grade together with the exposure environment, as the choice between 1.4301, 1.4404 and duplex 1.4462 depends on chloride exposure and required strength.
- Specify bar lengths and quantities, keeping in mind that laser welded stainless steel beams can be supplied in lengths up to 15 m.
- Define surface finish requirements, particularly for exposed architectural structures, hygienic environments or sections that will be polished after delivery.
- Declare the downstream operations, such as welding, drilling or machining, so that tolerances and residual stress can be assessed against the actual use of the section, as explained in our article on steel profile tolerances.
- Ask whether a non-standard section fits better: laser welding allows different flange and web thicknesses within one section, which can reduce weight compared with moving up to the next standard size. Montanstahl’s Technical Q&A covers the most common cases.
Frequently Asked Questions
For projects that need corrosion resistant structural sections, Montanstahl produces stainless steel IPE and HEA, HEB and HEM beams by laser welding, alongside custom steel and stainless steel profiles with tailored dimensions. Browse our case studies for real-world examples, see the industries we serve, or get a quote to discuss the sections your project requires.